Solenoid Valve Plastik DC12V 1/2 inch

STOCK READY INLET (tekanan minimal 0.02MPA) dan OUTLET (tekanan minimal 0MPA), SILAHKAN TULIS KEBUTUHAN PADA KETERANGAN, TANPA PENULISAN AKAN KAMI KIRIM SERI INLET

Purpose:
Used in automatic control systems: Solar automatic Sheung Shui, infrared sensors, sanitary ware, shower, drinking fountains, water control, water vending machines, water boilers, campus card equipment, switching control, the inlet end and the outlet port 180 angle, called http straight or linear valve!

Common solenoid valve parameters are as follows:

1. Normally closed (ie power-water)


2. The inlet valve (working pressure, 0.02-0.8MPa),


3. Installation angle: parallel (180 degrees)


4. Interface: 4 charge that is G1 / 2 20mm!


5. Voltage: DC12V

Info harga dan stok update klik : Solenoid Valve Plastik DC12V 1/2 inch

Koleksi lengkap kunjungi www.PusatKomponen.com

Sensor Arus Lemah Breakout ACS712 SparkFun

Description:

This current sensor gives precise current measurement for both AC and DC signals. These are good sensors for metering and measuring overall power consumption of systems. The ACS712 current sensor measures up to 5A of DC or AC current. We added an opamp gain stage for more sensitive current measurements. By adjusting the gain (from 4.27 to 47) you can measure very small currents.

The ACS712 Low Current Sensor Breakout outputs an analog voltage that varies linearly with sensed current. To calibrate, first set the output offset to the desired level (with zero current on the sense lines, read output with a DVM). Then with a known current input (a 100mA limited supply works well for this), set the output deflection with the gain pot. Sensitivity is then calculated as (Vref - Vdeflect)/(current input).

The bandwidth on the ACS712 Low Current Sensor Breakout has been set to 34kHz to reduce noise when using at high gains. The full 80KHz bandwidth that the sensor is capable of can be recovered by removing C1. See schematic for more details.

Documents:

ACS712 Datasheet : sparkfun.com/datasheets/BreakoutBoards/0712.pdf
GitHub : github.com/sparkfun/Low_Current_Sensor_Breakout-ACS712/tree/V_1.4a

Info harga dan stok update klik : Sensor Arus Lemah Breakout ACS712 SparkFun

Koleksi lengkap kunjungi www.PusatKomponen.com

FLiR Dev Kit - Sparkfun

Description:

The FLiR Dev Kit includes a breakout as well as a Lepton longwave infrared (LWIR) imager. With this kit you will be able to bring FLiRs thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. All you need to do to get this kit set up, simply attach the Lepton imager module into the provided breakout, connect the headers, and you will be seeing in full darkness in no time!

The Lepton LWIR module included in each FLiR Dev Kit acts as a sort of camera and packs a resolution of 80 60 pixels into a camera body that is smaller than a dime and captures infrared radiation input in its nominal response wavelength band (from 8 to 14 microns) and outputs a uniform thermal image. Meanwhile, each breakout board in these kits provides the socket for the Lepton, power supplys, 25Mhz Crystal Oscillator, 100 mil header for use in a breadboard or wiring to any host system. A few things to consider about this kit: the breakout board will accept a 3-5V input and regulate it to what the Lepton wants, to read an image from the lepton module all you need is an SPI port, and to configure the camera settings you also need an I2C port, although this is not required.

Note:

This kit comes in two separate parts and will need to be assembled once received. The Lepton module is extremely sensitive to electrostatic discharge (ESD). When inserting it into the breakout board be sure to use proper personal grounding, such as a grounding wrist strap, to prevent damage the module.

Deskripsi lengkap dan contoh code silahkan cek sparkfun.com/products/13233

Info harga dan stok update klik : FLiR Dev Kit - Sparkfun

Koleksi lengkap kunjungi www.PusatKomponen.com

LCD 7 inch HMI Touch Nextion Enhanced NX8048K070

Features
-Support built-in RTC
-Support GPIO
-SD Card interface: support max max 32G Micro TF/SD card (FAT32 file format)
-Flash data storage space: 32MB
-EEPROM: 1024 byte
-RAM: 8192 byte
-Instruction buffer: 1024 byte
-Color65K (65536) colors
-Resolution800480 pixel
-Adjustable Brightness:0~230 nit, the interval of adjustment is 1%

Specification
-Visual Area: 154.08mm(L)85.92mm(W)
-Layout size: 181(L)108(W)9.3(H)
-Touch type: Resistive
-BacklightLED
-Backlight lifetime (Average): >30,000 Hours
-Net Weight: 268 g
-Recommended power supply: 5V 2A

Package includes
-1 7.0" Nextion Enhanced HMI Display
-1 power supply test board
-1 4-pin grove cable

Documents
Please visit our wiki page (wiki.iteadstudio.com/NX8048K070) for more info about this product. It will be appreciated if you can help us improve the documents by correcting the errors, adding more demo codes or tutorials.

Info harga dan stok update klik : LCD 7 inch HMI Touch Nextion Enhanced NX8048K070

Koleksi lengkap kunjungi www.PusatKomponen.com

Case OrangePi Lite

Case untuk orangepi lite
Warna hitam transparant

Info harga dan stok update klik : Case OrangePi Lite

Koleksi lengkap kunjungi www.PusatKomponen.com

Sensor PIR Motion Parallax

Description
-Longer detection range, selectable by onboard jumper
-Wider supply voltage, from 3 to 6 VDC
-Easy interface to any microcontroller
-Small size makes it easy to conceal

The Parallax PIR Motion Sensor is a pyroelectric device that detects motion by measuring changes in the infrared (heat) levels emitted by surrounding objects. When motion is detected the PIR Sensor outputs a high signal on its output pin.

Features
-Detect a person up to - 30 ft. away, or up to 15 ft. away in reduced sensitivity mode
-Jumper selects normal operation or reduced sensitivity
-Source current up to 12 mA @ 3 V, 23 mA @ 5 V
-Mounting holes for 2-56 sized screws
-3-pin SIP header ready for breadboard or through-hole projects

Info harga dan stok update klik : Sensor PIR Motion Parallax

Koleksi lengkap kunjungi www.PusatKomponen.com

Kercan Barcode Scanner KR8120 USB Interface Auto Scanning

Keunggulan :

1. Auto sensing scanning


2. High efficient power full decoding


3. Intelligent smart sensing, Using a highly efficient optical technology and supported by high speed kernel architecture, the fast read high-precision bar code


4. Plug and play tanpa driver, multi platform OS


5. Desain anggun dan tahan banting

Info harga dan stok update klik : Kercan Barcode Scanner KR8120 USB Interface Auto Scanning

Koleksi lengkap kunjungi www.PusatKomponen.com

XSP Arduino Programmer - DFRobot

INTRODUCTION

XSP Programmer is designed for Arduino/AVR device. It is a driver free programmer, supporting Arduino/AVR ISP and FTDI programming.

It could provide both 5V and 3.3V power output or self-adaption power output(OFF mode).

Support Xbee socket and auto-match ISP clock frequency.

With this programmer, you can adjust its interface for your own device. Quite convenient and easy to use. It will be your good friend, when you coding and programming.

It could work with eClip programming Fixture together.

FEATURES

Multi-function
Support Arduino/AVR ISP programming
Support Arduino FTDI programming
Support serial port communication
Flexible Power Management
Support 5V/3.3V power output/self-adaption power output(OFF mode)
When you turn off the output power, it will auto-match objective voltage.
Power output warning (When the output power mismatch objective voltage, the warning led will be light)
Automatic short-circuit protection
Free Driver
Free driver in MacOS and Linux
Arduino IDE builtin driver in Windows
High Efficiency
Max 2MHz clock frequency in ISP mode
Auto-match ISP uoloading speed (Compatible with devices such as 1MHz bare chip and 16MHz Arduino UNO)
Max 250000bps serial port baud rate in FTDI mode
Easy to use
Serial port configuring working mode
Help menu
Led status indicator
DFU firmware upgrading method

Reference 
https://www.dfrobot.com/wiki/index.php?title=XSP_-_Arduino_Programmer_SKU:DFR0360

 

Info harga dan stok update klik : XSP Arduino Programmer - DFRobot

Koleksi lengkap kunjungi www.PusatKomponen.com

Sensor GY-906 MLX90614 Infrared Temperature

Description

This is a MELEXIS MLX90614ESF-BAA-000-TU-ND non-contact infrared thermometer for use with Arduino, or any microcontroller that can communicate with it through it's I2C interface.

Features

1. Small size, low cost


2. Mounted on a breakout board with two types of pins


3. 10k Pull up resistors for the I2C interface with optional solder jumpers


4. Easy to integrate


5. Factory calibrated in wide temperature range:-40+125C for sensor temperature and -70+380C for object temperature.


6. High accuracy of 0.5C over wide temperaturerange (0+50C for both Ta and To) High (medical) accuracy calibration


7. Measurement resolution of 0.02C


8. Single and dual zone versions


9. SMBus compatible digital interface


10. Customizable PWM output for continuousreading


11. Simple adaptation for 8-16V applications


12. Sleep mode for reduced power consumption


13. Different package options for applications andmeasurements versatility


14. Automotive grade


15. Applications Examples


16. High precision non-contact temperature measurements


17. Thermal Comfort sensor for Mobile AirConditioning control system


18. Temperature sensing element for residential,commercial and industrial building airconditioning


19. Windshield defogging


20. Automotive blind angle detection


21. Industrial temperature control of moving parts


22. Temperature control in printers and copiers


23. Home appliances with temperature control


24. Healthcare


25. Livestock monitoring


26. Movement detection


27. Multiple zone temperature control up to 127sensors can be read via common 2 wires


28. Thermal relay / alert


29. Body temperature measurement

Info harga dan stok update klik : Sensor GY-906 MLX90614 Infrared Temperature

Koleksi lengkap kunjungi www.PusatKomponen.com

GY-52 MPU-6050 3-Axis Gyroscope Accelerometer Module

Features
Chip: MPU-6050; Power supply :3-5V (internal low dropout regulator); Communication modes: standard IIC communication protocol; Chip 16bit AD converter, 16-bit data output; The gyroscopes range: +/- 250 500 1000 2000 degree / s; Acceleration range: +/- 2 +/- 4 +/- 8 +/- 16g; 2.45mm pin pitch

Application
Motion sensing game; Augmented Reality; Electronic Image Stabilization (EIS: Electronic Image Stabilization); Optical image stabilization (OIS: Optical Image Stabilization) Pedestrian Navigator; Zero-touch gesture user interface; The postures quick way; Perfect for smart phone; tablet device equipment; handheld games; 3D remote control; portable navigation devices

Packing List
1 x Module
1 x Straight 2.45mm 8-pin header
1 x Right angle 2.45mm 8-pin header

Dimensions: 0.91 in x 0.91 in x 0.08 in (2.3 cm x 2.3 cm x 0.2 cm)
Weight: 1.09 oz (31 g)

Info harga dan stok update klik : GY-52 MPU-6050 3-Axis Gyroscope Accelerometer Module

Koleksi lengkap kunjungi www.PusatKomponen.com

Omni Hub 18023 4mm (Universal Hubs)

SPECIFICATION

4 mm coupling allows the wheel mounting robot mechanisms and the motor shaft. It is designed to connect the 48 mm aluminum omni-directional wheels and motors 14148.

Key feature:
For connecting the 48 mm aluminum wheels and omni-directional motor

Material: Aluminum
outer diameter: 20MM
Bore length: 14mm inner diameter: 4mm
Net Weight: 5g

Compatible round:
48 mm aluminum omnidirectional wheel 14148

Info harga dan stok update klik : Omni Hub 18023 4mm (Universal Hubs)

Koleksi lengkap kunjungi www.PusatKomponen.com